ÊÇ·ñ½ø¿Ú£º | ·ñ | ³§¼Ò(²úµØ)£º | Öйú |
---|---|---|---|
Åƺţº | ENH3500 | ÓÃ;¼¶±ð£º | ×¢ËÜ |
PROPERTIES | TYPICAL VALUES | UNITS | TEST METHODS | |
---|---|---|---|---|
FLAME CHARACTERISTICS | 1) | |||
UL Yellow Card Link | E45329-100208982 | - | - | |
UL Recognized, 94-5VA Flame Class Rating | ≥3 | mm | UL 94 | |
UL Recognized, 94-5VB Flame Class Rating | ≥2 | mm | UL 94 | |
UL Recognized, 94V-0 Flame Class Rating | ≥0.8 | mm | UL 94 | |
Glow Wire Ignitability Temperature, 3.0 mm | 700 | °C | IEC 60695-2-13 | |
Glow Wire Ignitability Temperature, 2.0 mm | 700 | °C | IEC 60695-2-13 | |
Glow Wire Ignitability Temperature, 1.5 mm | 700 | °C | IEC 60695-2-13 | |
Glow Wire Ignitability Temperature, 0.8 mm | 750 | °C | IEC 60695-2-13 | |
Glow Wire Flammability Index, 3.0 mm | 960 | °C | IEC 60695-2-12 | |
Glow Wire Flammability Index, 2.0 mm | 960 | °C | IEC 60695-2-12 | |
Glow Wire Flammability Index, 1.5 mm | 960 | °C | IEC 60695-2-12 | |
Glow Wire Flammability Index, 0.8 mm | 960 | °C | IEC 60695-2-12 | |
Oxygen Index (LOI) | 31 | % | ASTM D2863 | |
Oxygen Index (LOI) | 31 | % | ISO 4589 | |
MECHANICAL | 2) | |||
Tensile Stress, yld, Type I, 50 mm/min | 44 | MPa | ASTM D638 | |
Tensile Stress, brk, Type I, 50 mm/min | 42 | MPa | ASTM D638 | |
Tensile Strain, yld, Type I, 50 mm/min | 3 | % | ASTM D638 | |
Tensile Strain, brk, Type I, 50 mm/min | 10 | % | ASTM D638 | |
Tensile Modulus, 5 mm/min | 3150 | MPa | ASTM D638 | |
Flexural Stress, yld, 1.3 mm/min, 50 mm span | 77 | MPa | ASTM D790 | |
Flexural Modulus, 1.3 mm/min, 50 mm span | 2750 | MPa | ASTM D790 | |
Tensile Stress, yield, 50 mm/min | 39 | MPa | ISO 527 | |
Tensile Stress, break, 50 mm/min | 38 | MPa | ISO 527 | |
Tensile Strain, yield, 50 mm/min | 3 | % | ISO 527 | |
Tensile Strain, break, 50 mm/min | 8 | % | ISO 527 | |
Tensile Modulus, 1 mm/min | 3200 | MPa | ISO 527 | |
Flexural Stress, yield, 2 mm/min | 70 | MPa | ISO 178 | |
Flexural Modulus, 2 mm/min | 2700 | MPa | ISO 178 | |
IMPACT | 2) | |||
Izod Impact, notched, 23°C | 40 | J/m | ASTM D256 | |
Izod Impact, unnotched, 23°C | NB | J/m | ASTM D4812 | |
Izod Impact, notched 80*10*4 +23°C | 5 | kJ/m² | ISO 180/1A | |
Izod Impact, notched 80*10*4 -30°C | 5 | kJ/m² | ISO 180/1A | |
Izod Impact, unnotched 80*10*4 +23°C | NB | kJ/m² | ISO 180/1U | |
Izod Impact, unnotched 80*10*4 -30°C | NB | kJ/m² | ISO 180/1U | |
Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm | 6 | kJ/m² | ISO 179/1eA | |
Charpy 23°C, Unnotch Edgew 80*10*4 sp=62mm | NB | kJ/m² | ISO 179/1eU | |
THERMAL | 2) | |||
HDT, 0.45 MPa, 3.2 mm, unannealed | 160 | °C | ASTM D648 | |
HDT, 1.82 MPa, 3.2mm, unannealed | 60 | °C | ASTM D648 | |
Vicat Softening Temp, Rate B/50 | 170 | °C | ASTM D1525 | |
CTE, -40°C to 95°C, flow | 8.00E-05 | 1/°C | ASTM E831 | |
CTE, -40°C to 95°C, xflow | 8.00E-05 | 1/°C | ASTM E831 | |
Ball Pressure Test, 125°C +/- 2°C | PASSES | - | IEC 60695-10-2 | |
Vicat Softening Temp, Rate B/120 | 170 | °C | ISO 306 | |
Vicat Softening Temp, Rate B/50 | 170 | °C | ISO 306 | |
HDT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm | 60 | °C | ISO 75/Af | |
HDT/Bf, 0.45 MPa Flatw 80*10*4 sp=64mm | 160 | °C | ISO 75/Bf | |
Relative Temp Index, Elec | 1) | 150 | °C | UL 746B |
Relative Temp Index, Mech w/impact | 1) | 105 | °C | UL 746B |
Relative Temp Index, Mech w/o impact | 1) | 150 | °C | UL 746B |
PHYSICAL | 2) | |||
Moisture Absorption, (23°C/50% RH/24 hrs) | 0.08 | % | ASTM D570 | |
Water Absorption, (23°C/24hrs) | 0.35 | % | ASTM D570 | |
Specific Gravity | 1.31 | - | ASTM D792 | |
Mold Shrinkage on Tensile Bar, flow | 4) | 1.8-2.8 | % | SABIC method |
Density | 1.31 | g/cm³ | ISO 1183 | |
Melt Volume Rate, MVR at 250°C/2.16 kg | 20 | cm³/10 min | ISO 1133 | |
Moisture Absorption (23°C / 50% RH) | 0.08 | % | ISO 62 | |
Water Absorption, (23°C/saturated) | 0.35 | % | ISO 62-1 | |
ELECTRICAL | 2) | |||
Volume Resistivity | >1.E+15 | Ω.cm | ASTM D257 | |
Comparative Tracking Index (UL) {PLC} | 0 | PLC Code | UL 746A | |
Volume Resistivity | >1.E+15 | Ω.cm | IEC 60093 | |
Surface Resistivity, ROA | >1.E+15 | Ω | IEC 60093 | |
Comparative Tracking Index | 1) | 525 | V | IEC 60112 |
Hot-Wire Ignition (HWI), PLC 2 | ≥3 | mm | UL 746A | |
Hot-Wire Ignition (HWI), PLC 3 | ≥1.5 | mm | UL 746A | |
Hot-Wire Ignition (HWI), PLC 4 | ≥0.8 | mm | UL 746A | |
High Amp Arc Ignition (HAI), PLC 0 | ≥0.8 | mm | UL 746A | |
INJECTION MOLDING | 3) | |||
Drying Temperature | 110-120 | °C | ||
Drying Time | 2-4 | Hrs | ||
Maximum Moisture Content | 0.02 | % | ||
Melt Temperature | 245-260 | °C | ||
Nozzle Temperature | 230-255 | °C | ||
Front - Zone 3 Temperature | 240-260 | °C | ||
Middle - Zone 2 Temperature | 235-250 | °C | ||
Rear - Zone 1 Temperature | 230-240 | °C | ||
Hopper Temperature | 40-60 | °C | ||
Mold Temperature | 40-100 | °C |
ÎÒ¹«Ë¾³¤ÆÚÌṩ¡¾VALOX ENH3500 ·ÇÂÈ»¯¡¢·Çä廯×èȼ¼ÁPBT¾ßÓÐUL V0µÈ¼¶¡¿£¬Èç¹ûÄú¶ÔÎÒÃǵġ¾VALOX ENH3500 ·ÇÂÈ»¯¡¢·Çä廯×èȼ¼ÁPBT¾ßÓÐUL V0µÈ¼¶¡¿¸ÐÐËȤ£¬ÇëËæʱ²¦´òÏ·½µÄµç»°£¬µã»÷ÁôÑÔ»òQQÓëÎÒ½»Ì¸¡£ÁªÏµÎÒʱ£¬Çë˵Ã÷ÊÇÔÚ¹©Ó¦ÉÌÍøÉÏ¿´µ½µÄ£¬Ð»Ð»£¡
ÁªÏµÈË | ÎâÏÈÉú |
---|---|
ÊÖ»ú | 𐂿𐃀𐂿𐃁𐃂𐃃𐃃𐃄𐃃𐃄𐃀 |
µØÖ·£º¹ã¶« ¶«Ý¸ ÕÁľͷÕò ÏÈÍþ´óµÀ85-1ºÅËܽºÉÌÎñÖÐÐĶþÆÚ9¶°32ºÅ ÊÖ»ú£º𐂿𐃀𐂿𐃁𐃂𐃃𐃃𐃄𐃃𐃄𐃀
¶«Ý¸ÊоۺÆËÜ»¯ÓÐÏÞ¹«Ë¾ ¼¼ÊõÖ§³Ö£º¹©Ó¦ÉÌÍø | Òƶ¯Õ¾